PM9 and Lakeline followers

[Tpepper70]

I promised a review to Alfonse and hear it is. I received the follower in 4 days. Should've been 3 but I have a slow PO. I ordered it because I had a broken follower in 1 of the mags I received when I traded for my blunt nose PM9. I decided to install it in my 6 round carry mag instead of the extended mag. It fit perfectly, looks great, works even better and,,,,,,,,I can load a mag, with the slide down, and slingshot the slide with no issues at all. I can even ride the slide very slowly and it still goes into battery. Holds the slide open on last round and fired all 4 mags flawlessly. Top notch part, top notch material and over the top business. I'll be ordering more for the rest of my mags. Thanks so much, Alfonse, for offering a superb product. Y'all need to get ya some.

Cruce Dum Spiro Fido

[Alfonse]

Super, thank you for the great review!

[Nytcrawler93]

I received mine as well and they functioned perfectly. The only thing I noticed was that the slide has to be pulled back fractionally further to sling shot but it always works. I also noticed one of my springs was installed backwards from the factory....overall the product is nails.


Sent from my iPhone using Tapatalk

[MBSL500]

Any reports on how well these followers are working in the 7 round magazines?

[Tpepper70]

I haven't tried them in my 7 rounders yet. I'm sure Alfonse has and will be along to clarify.

Cruce Dum Spiro Fido

[Alfonse]

They work fine for me. They will only improve feeding.

[Wag2323]

I have the followers in two seven round mags for my CW9 and have no issues.

[adman]

I ordered a couple of followers today, largely because I want to make the pistol work more fluidly with its owner, not because I consider dropping the release a hassle. I'm currently auditioning a heavier outer recoil spring (10.5 lbs.) from Wolfe as well. I'm seeking some minor mods to improve my experience and accuracy. I hope they get them shipped before they go on vacation (March 20). They said so long as you got them ordered by Saturday afternoon, which I did... ;-)

[Bawanna]

Al will come through for you, have no doubt. Take it to the bank and draw interest.

[rowdy115]

I have these followers in all my CM9 mags and all work and/or cycle great. I have 2 six rounders, 1 seven rounder, and 1 eight rounder. All factory Kahr mags but with Al's followers. The only one I still have trouble being able to sling shot a round with is the 8 rounder, but that's a back up mag only anyway so I figure the slide will be locked back when I load that bad boy and I can just hit the slide release and be ready to rock...

[Nytcrawler93]

I run them in every capacity mag. No stoppages yet of any sort.


Sent from my iPhone using Tapatalk

[Alfonse]

I ordered a couple of followers today, largely because I want to make the pistol work more fluidly with its owner, not because I consider dropping the release a hassle. I'm currently auditioning a heavier outer recoil spring (10.5 lbs.) from Wolfe as well. I'm seeking some minor mods to improve my experience and accuracy. I hope they get them shipped before they go on vacation (March 20). They said so long as you got them ordered by Saturday afternoon, which I did... ;-)

They shipped. I shipped all orders that were taken. I stopped orders except those from the 3d printer until we are shipping again. Thanks!

[adman]

They shipped. I shipped all orders that were taken. I stopped orders except those from the 3d printer until we are shipping again. Thanks!

Thank you, sir. I appreciate it.

[Alfonse]

Thank you, sir. I appreciate it.

Absolutely! Hopefully your received your confirmation and tracking number. Thanks again.

[jayo84]

Lakeline follower took a 7rd mag for my cm9 from totally unreliable to totally unstoppable! Unreal the improvement! I would trust my life to this mag now! Lakeline FTW