New knife for Kahr owners

[downtownv]

My Fav!

Pro-Tech Knives
Brend Auto #3 (medium)

Specs
Blade:
154-CM Stainless Steel, 3.75" Long Blade, .125" thick, 59RC
Handle:
6061-T6 Aluminum, 5" Long, 1.15" Wide, 0.45" Thick
Blade
154-CM Stainless Steel, 3.75" Long, 1.06" Wide, 0.125" Thick
Weight:
approximately 4 ounces
This mid size piece is the perfect companion to our Brend #1 (Large) and Brend #2 (Small) Auto knife series. Available in a great many variations, the Medium Brend Auto is a great new addition to our line of knives. Super slender, lightweight, and awesome 3.75” Brend designed blade = cutting power! Each Brend #3 Auto is fitted with a stainless pocket clip for tip up carry. Hold on tight, this one has INCREDIBLE Coil Spring Action!

[downtownv]

My Fav!

Pro-Tech Knives
Brend Auto #3 (medium)

Specs
Blade:
154-CM Stainless Steel, 3.75" Long Blade, .125" thick, 59RC
Handle:
6061-T6 Aluminum, 5" Long, 1.15" Wide, 0.45" Thick
Blade
154-CM Stainless Steel, 3.75" Long, 1.06" Wide, 0.125" Thick
Weight:
approximately 4 ounces
This mid size piece is the perfect companion to our Brend #1 (Large) and Brend #2 (Small) Auto knife series. Available in a great many variations, the Medium Brend Auto is a great new addition to our line of knives. Super slender, lightweight, and awesome 3.75” Brend designed blade = cutting power! Each Brend #3 Auto is fitted with a stainless pocket clip for tip up carry. Hold on tight, this one has INCREDIBLE Coil Spring Action!

[Barth]

My favorite knife is a Cold Steel Safe Maker I

[Pulpit Pistol]

I love all my Spydercos, been thru a number of them over the years. Wore a couple of them out during my excessive rock climbing and backpacking years. Just hard on them.


Some of them they make here, some are made overseas. But I have one of the newer Chinese models (Tenacious) and it's a pretty decent knife. I'm not a knife guy though. I only keep a few folders (all Spydercos) here and there for general use. They kinda run the gambit on the quality of the steel, from some carbon stuff, to surgical steel, etc. Just depends on where they come from as to the quality, but like I said, even the cheap stuff is pretty good.


I doubt the Kahr knife is made here, but it's possible. But wherever the regular Delica is made...should be the same. I know at one point, they only made knives of a certain steel type out in Colorado somewhere. Everything else was made in China, Japan, etc.

My only Spyderco is the "big brother" of the Delica, the Endura. Mine is the Endura 4 Full Flat Ground. I prefer the FFG to the saber grind being offered in the Spyderco/Kahr affiliation. The VG 10 steel-made knives are produced in Seki City Japan. The Japanese make GREAT blades.

[Captquest]

I guess $99 is about right for a special edition with Kahr logo on the blade (very cool), I just ordered a Kershaw Hinderer for $30, more my budget at the moment.

[Short Bus]

I guess $99 is about right for a special edition with Kahr logo on the blade (very cool), I just ordered a Kershaw Hinderer for $30, more my budget at the moment.

There are some good budget blades in the $30 price range, Cr13MoV or AUS-8 aren't bad steels for the money.

The Ka Bar Dozier is a nice knife for the money ($15-$20) My wife has one of the pink breast cancer Doziers (she went through breast cancer a couple years ago)

http://www.amazon.com/KA-BAR-Dozier-...s=kabar+dozier

[ParabellumJ]

New knife for Kahr owners

I love the Delica 4. I have 2 and for me it's a toss up between my Delica 4 or Benchmade Mini Griptillian for my best small EDC folder. Factoring normal prices the I give the edge to Spyderco. I also love the Spyderco Tenancious for a budget folder. I have a Kershaw Blur with S30V steel and it's a great knife as well. Price on the Kahr Delica 4 is a bit high, and blade length a little short. My EDC companions...

[Short Bus]

I did that with my Spyderco Persistence

I have a Hornady Buck Vantage Pro on it's way, should be here tomorrow. It's hard to beat S30V steel and G10 scales for about $50 shipped.

http://www.hornady.com/store/Hornady-Buck-Knife/

DO NOT BUY THE HORNADY VANTAGE PRO

It is NOT a Vantage Pro, it's a Vantage Force Select!!! It's FRN scale and 420 steel. Way over priced @ $50 shipped!!!

I sent the Hornady knife back, Hornady is giving me a full refund (including shipping) and sent me a return shipping label.

I ordered a Vantage Pro to replace it

http://www.ebay.com/itm/181191522917...84.m1497.l2649

[yqtszhj]

It's a fire starting thingy - survival knife stuff.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Now you've done it. I've got to have one.

[warbird1]

Spyderco and Kahr team up
http://www.shootingwire.com/story/307576

That's a big maybe for me.

[Barth]

Now you've done it. I've got to have one.

IMHO - The standard model is a real deal @ $45
http://www.amazon.com/Gerber-Grylls-...s+ultimate+pro

There is a newer upgraded version with a sharpener on the sheath @ $74
http://www.amazon.com/Gerber-Grylls-...s+ultimate+pro

http://www.gerbergear.com/Survival/K...-Pro_31-001901

[Short Bus]

IMHO - The standard model is a real deal @ $45
http://www.amazon.com/Gerber-Grylls-...s+ultimate+pro

There is a newer upgraded version with a sharpener on the sheath @ $74
http://www.amazon.com/Gerber-Grylls-...s+ultimate+pro

http://www.gerbergear.com/Survival/K...-Pro_31-001901

I found it for $35, in case anyone wants one

http://www.ebay.com/itm/Gerber-Ultim...item35d06a23f3