Load problems

[thumbs]

I have been loading 115gr Jrn with w123 with 4.5 gr. I am having terrible results so far. Now I think I know the problem but maybe someone can help me. I oal is 1.170. I think I am to long for the cm9. Works fine in my Glock but terrible in the cm9. I just re seated the rest of the cartridges to 1.150.

Do you guys think this is the reason for all the ftf fte? This is a brand new pistol first time out. Shot about 20 rounds and had about 18 of then give me problems.

I cleaned and lubes the pistol before taking it out. I also checked the magazine to make sure the follower moved freely. I also racked the slide about 300 times before shooting it.

Next time I'll use factory ammo I just didnt have any today.

Thanks for the help

[Bawanna]

I suspect your correct. While not finicky about ammo Kahrs don't seem to like cartridges that are on the long side.

I'd definitely run some factory till your good and broke in and then experiment with the hand loads. I did very similar stuff with my PM45. Shortened up the OAL just a bit and they work just fine.

[Scimmia]

1.150 is even pretty long. Using 125 gr LRN bullets, 1.130 was just barily too long for my CM9 chamber and contacting the rifling. I'm sure the bullet profile has a lot to do with that, though. 1.125 was fine, but I load most of them at 1.120 now.

[thumbs]

Thanks guys. I am so new to Kahr I didn't know they were so sensitive. My Glock really doesn't care. LoL

The only reason I went to 1.150 was that was the length of the factory stuff I got this afternoon.

Ok so I can still go a bit shorter if I have to. I hope with the profile of the 115 gr 1.150 will work.

I loaded a mag with the 1.150 oal stuff I just loaded. I put it in the pistol and ran them through the pistol by racking the slide. I know this isn't a guarantee but they ran through just fine. I hope to shoot the 1.150 tomorrow.
Thanks

[Tilos]

thumbs:
You left the 2nd "1" out of the OAL you mentioned three times in both your posts.
I'm hoping you mean 1.150" and not the number you posted.
Tilos

[thumbs]

Thanks yeah 1.150 is correct. My original reloads were 1.170.
I have racked three or four mag through by hand tonight without a problem. I'm looking forward to getting out tomorrow. I think it will be night and day difference.

[MW surveyor]

thumbs,

I've been running my 9 mm 125 grain LRN loads at 1.115 to 1.125 using 4.4 grains of HP 38. Cycles the slide very well and is an accurate load in my CW 9 and CZ Phantom.

Not trying to get on to you but when you describe something regarding reloading, accuracy is everyone's friend (especially with the numbers!).

[thumbs]

Yep your right. It was one of those things where my mind said one thing and my fingers said another.

I was wrong with the info I posted. This is exactly why no one should try any load unless they can confirm its accuracy. If there is anything fortunate about my mistake is the round would probably not chamber I'll see if I can find that load in my book.

Are you casting your own lead bullets, buying them or buying the loaded cartridge? If you are casting your own what mold are you using


Thanks

[MW surveyor]

Not casting my own at the present time but buying the bullets from friendswood bullet company.

BTW - I always do a "plonk" test for each of my new bullet reloads for any semi auto. That is, I remove the barrel from the gun and test the round to make sure it sits properly at the lock up or back of the chamber. Then I make sure that it fits in the magazine and will cycle by hand. You can see how the reload should sit by using a factory round that you know works in your gun.

[thumbs]

Thanks. I am using jacketed round nose bullets now. Those boys ain't cheap. How much do you figure the lead bullets are a piece. My jrn are about .10 cents..

I will try your test tonight.

The good news is I got to shoot the cm this morning with Fedral factory ammo. I ran 50 rounds through it and it ran flawlessly! I then ran 50 rounds of my reloads that I shortened the oal on and the ran much better not good but much better than yesterday. They were 1.150 in length. I will load the next batch shorter, 1.125 or 1.130 and see how they run. Now I know, or am pretty sure the factory stuff works. My reloads were the same length but I did have some failures. Not sure why. It may just be the bullets are just a little different and need a shorter oal.

[MW surveyor]

The 9 mm run $29.00 per 500 or $58.00 per thousand without shipping. I usually order 500 or 1000 rounds of 9 mm, 357 and 45 cal each time for a flat rate shipping of $15.00 per 60 pounds. Lets call it $63.00 then for 1000 rounds of 9 mm or $0.063 per round.

Make sure that your taper crimp is enough to hold the bullet and also the shape of the round plays a big part. If you are setting too deep you may be trying to taper crimp on the ogive. If the round is too long, the mouth of the casing may not be making contact with the front of the chamber. They only way you can test this is by removing the barrel from your gun and inserting one of your reloads.

[thumbs]

Thanks

I just loaded and reseated about 50 rounds. I checked the bullets in the barrel and check it out with a factory Federal round. They look the same to me. I set the oal to 1.135 or very close. I also used a med crimp on the cartrage. I then racked them through by hand and they seemed fine.

Like I said before the factory Federals ran without a problem.

[MW surveyor]

As long as your reloads "plonked" in and you can turn the case without any binding, you should be good to go.

BTW - are you using a separate die for the taper crimp? I use the Lee taper crimp dies and do about a 3/4 to one full turn after contact with the bullet nose for my taper crimps. I also do a push test on the side of the bench to make sure that I got the crimp right. Light/moderate pressure on the head of the bullet against the side of the bench, then remeasure the COL. If it moved, crimp a bit tighter. JMTC YMMV

[thumbs]

Still playin a bit with the loads. I took a batch of reloads out today to give them a try. The oal was 1.135 using 4.3 gr of Wincheser 231. Well it ran very well. One stove pipe in 50 rounds. A lot better than at the beginning. Now I still have a little hitch though. The slide never held open on the last round with these rounds. I put a box of factory Federals through it and the slide held open on every mag. I think my reloads are a little soft. The book says they should be at 1010 fps while the Federals are 1125 fps. I can definitely feel the difference in the two. I'm gonna up the powder a bit, still within spec, and try goin back to 1.150 oal and see what happens. This "should" bring me very close to factory Federals.

We will see tomorrow.

[thumbs]

MW

I got your message in my email about a reply on the forum but when I go to the forum I don't have your message there. Anyway I read it in my email.

Yeah in my Lee book it says 4.8 grains so thats pretty close.

I think your right about the spring. It does really feels stiff. Well I guess that could be good or bad. Anyway looks like I gotta up my powder. I'm gonna go to 4.6 grains. Still under max. It will be interesting to see what happens. I am hoping 1.150 will work. Maybe from the start the loads were just a touch light.